BOAT MOTOR BRAIN

AJ's Boat Motor Brain

AJ's home base for boat motor work · built by Dad (Art) · Blue Collar Brains

Blue Collar Outlaws logo
PAGE COLOR
🤖 My Assistantinvoices, parts, questions 📷 Add Receipttap, then snap the photo 🔢 Fault CodesYamaha code lookup 🧮 Formulasprop, fuel, electrical math 📓 Job Journalyour day, in your words 🔧 Service Recordscustomers & who's due ⚓ Sea Time Logcaptain's license hours 📒 Side Job Booksaved invoices & parts 🎧 Study PackMaster Tech audio 📍 Landingsboat ramps near you 🌊 TidesBeaufort & the Lowcountry 🗺️ Depth Herechart depth + the tide 🎣 SeasonsSC shrimp, oysters, crab 📋 Licenses & Boat Paperworkstate links, one place

This is your shop in your pocket: talk to your assistant, keep your journal, track every customer's service, and study for that master test — all right here.

🛠️ AJ'S ASSISTANT — SIDE JOB BOOK

Talk to your assistant right here: tell it the job and it drafts the invoice, tell it a part and it reads it back clean for the book, tell it about your day and it writes up your journal entry, ask it a code or a formula and it answers off the reference below. Snap a receipt or a photo of the job with the 📷 button — it saves straight into your book. Your journal and your customers' service records live right under the chat. Under Service Records you can also hand each customer their own boat page — their service history and next due, on a link you text them. Dad can pop into this same thread and say hi.

Sea log photo: snap a picture of a paper sea-time log — the assistant reads it, shows you the days it found, and only logs them when you say yes.

🎧 Master Tech Study Pack

Son — you probably already know most of what's in here. This is just everything in one place, so the second run at that master test goes the way it should. Listen in the truck, tap the links, and go take what's yours.

🎧 The Audio Study Guide

Part 1 — The Test & What Trips People Up

Part 2 — The Study Plan & The Resources

First, the truth about this test

What trips people up

  1. The clock, not the knowledge. Diagnose in sequence — symptom → system → test. No wandering.
  2. The planted-fault practical under pressure. Real-world faults, not textbook ones.
  3. Electrical and ignition depth — stator output, charging amps at RPM, ion-sensing ignition on the V8.
  4. Fuel injection + YDIS — EFI pressures, sensor logic, live data and stored codes, knowing what's out of spec.
  5. The other engine family — 2-stroke questions catch 4-stroke techs, and the other way around.

The study plan

  1. Your own six course books first — the exam is drawn from them. Weakest module first (usually Electrical, then Fuel). Final class workbook = main cram source in the last two weeks.
  2. Daily listening rotation — Dangar Marine (diagnostic method) → Born Again Boating (systems theory) → Boats.net (factory procedures) → The Boater's Podcast (ears-only days).
  3. YDIS reps at the shop — run diagnostics on every job for a month. Live data, compare to spec, chase stored codes.
  4. Timed drilling — practice questions under a timer to rebuild test pace.

Resources (all free, all iPhone-friendly)

🔧 MECHANIC BRAIN — SHOP REFERENCE

The working half of this brain: Yamaha fault codes, the formulas, service intervals, tools, and the numbers — built to look up on the phone, mid-job, with greasy hands. Type a code number or a word and the list filters itself.

How codes are read

  • YDIS / YDS laptop — plugged into the diagnostic port under the cowling. Reads active + stored codes, live sensor data, engine-hour history, and runs actuator tests (injectors, coils, fuel pump).
  • Command Link gauges — many show the code number directly; some show a check-engine icon only.
  • Blink codes — no digital gauge? The check-engine light flashes it: long flashes (~1.5 sec) = first digit, short flashes (~0.5 sec) = second digit. 2 long + 3 short = code 23. Codes repeat in sequence with a ~3-second pause between them.
  • Codes cover EFI midrange and up (roughly 30 HP+). Stored codes can only be cleared with the diagnostic tool — fix the fault first, then clear.

Fault codes — the classic list

The code names the circuit the ECM is unhappy with — "common cause" is the usual real-world culprit. Confirm against the model's service manual; meanings can shift slightly by family (OX66/HPDI 2-strokes, F-series 4-strokes).

1
Normal — no faults
—
13
Incorrect pulser coil signal
Corroded/loose connector is #1; damaged harness; failed pulser coil. Test coil resistance before replacing
14
Incorrect crank position sensor signal
Sensor wiring, air gap, failed sensor
15
Incorrect engine temperature sensor signal
Wiring/connector first; test sensor resistance hot vs. cold; failed sensor. Can also ride along with a real overheat
17
Knock sensor
Sensor, wiring, or actual detonation (bad fuel, carbon, over-propped/lugging)
18
Incorrect throttle position sensor (TPS) signal
TPS misadjusted or failed, linkage binding, bad connection. Adjustment usually needs YDIS
19
Incorrect battery voltage
Low/weak battery, loose or corroded terminals, bad main ground, charging system fault. Check the battery and cables before anything electronic
22
Incorrect atmospheric pressure sensor signal
Sensor or wiring
23
Incorrect intake air temperature sensor signal
Loose/dirty connector most of the time; sensor rarely fails outright
25
Incorrect fuel pressure signal
Fuel pressure sensor circuit; verify actual rail pressure with a gauge before condemning parts
26
Incorrect injector signal
Injector circuit — wiring, connector, or injector itself
27
Incorrect water-in-fuel signal
Water actually in the fuel (drain the separator and look), or sensor/wiring
28
Incorrect shift position switch/sensor signal
Misadjusted shift cable is the classic cause; then switch/sensor and wiring. Can block starting
29
Incorrect intake air pressure sensor
Cracked/disconnected sensor vacuum hose, clogged hose, sensor
31
No tach signal output from ECU (OX66)
OX66 2-stroke specific
33
Ignition timing slightly corrected — cold engine start
Informational on OX66; normally not a fault to chase
35–38, 40
ECU processing information (OX66)
OX66 internal/ECU items — consult the OX66 manual
39
Oil pressure sensor
Sensor/wiring; verify real oil pressure mechanically if in doubt
41
Overrev control during ignition cutoff (OX66)
Informational — engine hit the limiter
42
Overheat control or no-oil control (OX66)
Real overheat or oil-system protection event — find the cause
43
Buzzer sounding (OX66)
Warning event logged
44
Incorrect engine stop lanyard switch signal
Lanyard switch, wiring, or the clip not seated
45
Shift cut off
Shift-interrupt event/circuit
46
Overheat switch
Overheat switch circuit tripped — check cooling (impeller, thermostat, intakes)
49
Over cooling
Thermostat stuck open is the classic cause
58
Failed to reach operating temperature (per PowerSportsGuide FAQ)
Thermostat stuck open / running too cold
59
ECM memory (trouble record only)
Stored-history marker
62 / 98
Low fuel pressure (same fault, listed both ways in public charts)
Weak high-pressure pump, clogged VST filter, restriction or air leak on the boat side, bad anti-siphon valve

Fault codes — VCT / OCV (V6 & V8)

Variable cam timing and oil control valve codes on the big motors, plus the V8 ion-sensing module.

24
EX cam position sensor
VCT/cam sensor circuit on applicable V6/V8 models
68
VCT (S bank) — starboard valve pulley abnormal advance
Variable cam timing, starboard bank (V6/V8)
69
VCT (P bank) — port valve pulley abnormal advance
Variable cam timing, port bank
71
S bank IN cam position sensor
Starboard intake cam sensor
72
P bank IN cam position sensor
Port intake cam sensor
73
OCV (S bank) — starboard oil control valve
VCT oil control valve circuit
74
OCV (P bank) — port oil control valve
VCT oil control valve circuit
85
IDM — ion current detection module
Ignition/ion-sensing module (large V8 models)

Fault codes — DEC / Helm Master

Drive-by-wire throttle (ETV/ETS), shift sensors, rigging and station lever codes. ETV = electronic throttle valve · ETS = electronic throttle system · SPS = shift position sensor · RCS = remote control system · MSLPS/SSLPS = main/sub station lever position sensors · APS = accelerator position sensor.

37
Intake air passage — electronic throttle valve (on DEC models)
Throttle body/ETV issue on drive-by-wire motors
75–82, 84
RCS — Remote Control System
DEC rigging faults. GAP: public charts list these only as "RCS" without per-code meanings — the model service manual or YDIS text is required
83
Trim/tilt angle sensor
Sensor or wiring
86
Y-COP immobilizer / theft deterrent
Key fob/immobilizer communication — check the fob battery first
87
Remote control system
DEC control fault
112
ETV ETS (ECM-sub)
Electronic throttle — sub-ECM
113
ETV ETS (ECM-system)
Electronic throttle system fault
114
ETV ETS (ECM-main)
Electronic throttle — main ECM
115
ETV ETS (throttle valve open)
Throttle valve stuck/open-side fault
116
ETV ETS (throttle valve closed)
Throttle valve closed-side fault
117
ETV ETS (driving motor P short)
Throttle motor circuit short
118
ETV ETS (driving motor N short)
Throttle motor circuit short
119
ETV ETS (driving motor connector open)
Throttle motor connector open
121
ETV ETS (communication error)
Throttle/ECM communication
122
ETV ETS (driving motor heat)
Throttle motor overheating
123
ETV ETS (driving motor relay)
Throttle motor relay
124
TPS MTPS open
Main throttle position sensor open circuit
125
TPS MTPS short
Main throttle position sensor short
126
TPS character fail
TPS signal out of expected character/range
127
TPS sub throttle position sensor open
Sub-TPS open
128
TPS sub throttle position sensor short
Sub-TPS short
129
ETV MTPS
Throttle valve/main TPS correlation
131–135
APS/ETV
Accelerator position sensor / throttle correlation faults (DEC)
136
ETV ETS comm. error main
Main channel communication
137
ETV ETS comm. error sub
Sub channel communication
138
ETV ETS (ECM main)
—
139
ETV ETS (ECM sub)
—
140
ETV
Electronic throttle valve general
141
ETV ETS throttle position sensor voltage
TPS supply/signal voltage
142
ETV ETS return spring
Throttle return spring check fault
143
ETV ETS comm. error
Communication error
144
ETV ETS low voltage mode
Low supply voltage to throttle system — check battery/charging first
145
ETV ETS throttle valve
Throttle valve fault
146–152
SPS — shift position sensor power/character faults
DEC shift sensor supply shorts/opens; 153 = shift motor over current; 154 = shift motor deadlock while stopping; 155 = shift motor deadlock while operating
156
Comm. error 1 — channel engine remote connector
DEC harness/connector
157
Comm. error 2 — channel engine remote connector
DEC harness/connector
160–181
MSLPS / SSLPS — main & sub station lever position sensor faults
Helm Master station lever sensors: power short/open, watching fail, character fail, per station 1 and 2
183
Station selector system fail
Helm Master
184
Lever selector system fail
Helm Master
186
Sub station communication error
Helm Master
187
Lever pickup abnormal
Helm Master
252
FC invalid code — engine overheat
Overheat event flag

Straight talk: Yamaha does NOT publish a free master code chart — the official charts live in each model's service manual and inside the dealer YDIS system. This list is the best public compilation, solid on the classic codes, thinner on the newest Helm Master sets. Codes 75–82 and 84 show in public charts only as "RCS" — per-code text needs the manual or YDIS.

Formulas

Theoretical top speed — prop math

(RPM × pitch) ÷ (gear ratio × 1056)

RPM = engine speed at full throttle · pitch = prop pitch in inches · gear ratio = the number before ":1" (2.00 for a 2.00:1 lower unit) · 1056 = the constant that turns inches/minute at the prop into mph.

Example: F150 at 5,800 RPM, 21″ pitch, 2.00:1 → (5,800 × 21) ÷ (2.00 × 1,056) = 121,800 ÷ 2,112 = 57.7 mph theoretical. No boat actually hits it — the gap is slip.

Prop slip

Slip % = ((theoretical − GPS speed) ÷ theoretical) × 100

Healthy slip at wide-open throttle: roughly 5–15%; heavy boats run higher. Very low slip with low RPM usually means over-propped. High slip can mean a spun hub, a damaged or ventilating prop, or the wrong prop.

Example: theoretical 57.7 mph, GPS says 50 → (57.7 − 50) ÷ 57.7 × 100 = 13.3% slip — normal.

Shop rule of thumb: 1 inch of pitch ≈ 150–200 RPM at WOT — more pitch drops RPM. (Shop practice, not a Yamaha spec.)

Ohm's law — the whole triangle

V = I × R  ·  I = V ÷ R  ·  R = V ÷ I  ·  P = V × I

V = volts · I = amps · R = ohms · P = watts.

Example: starter cables + connections carry 0.02 Ω and the starter draws 180 A cranking → 180 × 0.02 = 3.6 V lost in the cables. That's a no-crank with a "good" battery — why corroded terminals strand boats.

Voltage drop — test cables under load

Drop % = (volts dropped ÷ system volts) × 100

Meter probes on each end of the cable run while the circuit is working (cranking, pump running) — the meter reads the voltage wasted in that run. ABYC limits: max 3% on critical circuits (panel feeders, bilge, electronics), max 10% non-critical.

Example: 12.6 V battery, cranking, 0.42 V across the positive cable → 0.42 ÷ 12.6 = 3.3% — over the mark: clean or replace the cable ends before condemning the starter.

Related: AC ripple at the battery, engine ~2,000 RPM — over 250 mV AC means rectifier/regulator diodes are leaking.

Fuel burn estimate

WOT burn (GPH) ≈ horsepower ÷ 10

Cruise burn ≈ 40–60% of the wide-open number. Works across brands (gasoline BSFC math).

Example: F150 wide open → 150 ÷ 10 = ~15 GPH. At cruise (3,500–4,000 RPM) → roughly 6–9 GPH.

Range — with the Rule of Thirds

MPG = mph ÷ GPH  ·  Range = MPG × (tank × ⅔)

Plan on two-thirds of the tank: a third out, a third back, a third in reserve.

Example: 40-gallon tank, cruising 30 mph at 7.5 GPH → 30 ÷ 7.5 = 4.0 MPG · planning fuel 40 × ⅔ ≈ 26.7 gal → range ≈ 107 miles with the reserve intact.

Battery capacity & load math

Ah used = amps × hours  ·  Battery Ah needed = (amps × hours) ÷ 0.5

Only about half a lead-acid battery's rated amp-hours are usable without hurting it. CCA = starting rating; Ah = capacity rating.

Example: electronics + livewell draw 8 A over a 5-hour trip = 40 Ah used → battery should be at least 80 Ah rated.

Resting voltage (engine off, settled): ~12.6 V full · ~12.2 V half · under ~12.0 V discharged or failing. F115 battery spec: 430–1080 CCA, 70 Ah.

Conversions techs actually use

ConvertMathExample
mph → knots÷ 1.15146 mph = 40 knots
knots → mph× 1.15130 knots = 34.5 mph
inches → mm× 25.40.031″ gap ≈ 0.8 mm
mm → inches÷ 25.425 mm = 0.98″
N·m → ft-lb× 0.73825 N·m = 18.4 ft-lb (F115 plug torque)
ft-lb → N·m× 1.35640 ft-lb = 54 N·m
psi → kPa× 6.89544 psi = 303 kPa
US gal → liters× 3.78510 gal = 37.9 L
°F → °C(°F − 32) × 5/9140 °F = 60 °C
HP → kW× 0.746115 HP = 84.6 kW

Service intervals

Yamaha's schedule runs on hours or calendar — whichever comes first. This is the standard F-series four-stroke pattern; confirm against the model's manual.

Every trip / after every use
Freshwater flush (salt left in cooling passages is the #1 engine killer), check telltale flow, oil level check, prop and intake inspection, rinse powerhead periodically and spray with corrosion protectant (Yamalube Yamashield per Yamaha Outboards)
First 20 hours (or 3 months) — break-in service
Engine oil + filter change, gear oil change (removes break-in metal), inspect fuel filters and fuel/water separator, check plugs, torque/linkage/fastener check, full inspection, YDIS health report. (Note: a few dealer write-ups say 25 hours — Yamaha's published interval is 20 hours; follow the manual.)
Every 50 hours
Change the boat's fuel/water separator filter (per Yamaha Outboards midseason guidance); mid-season visual checks, lubrication points, anodes, battery, steering on heavy-use/saltwater boats
Every 100 hours (or 1 year) — the core annual service
Engine oil + filter, gear lube, fuel filters (incl. engine-mounted), spark plug inspection/replacement as needed, water pump inspection, thermostat check, anodes inspect, throttle/shift/steering checks, prop shaft lubrication, full systems inspection
Every 300 hours (or 3 years)
Everything in the 100-hour service plus water pump impeller replacement (replace at 300 hr/3 yr regardless of looks — impeller failure is the leading cause of serious overheat damage), thermostat replacement (per Yamaha Outboards), valve clearance check on applicable models, timing belt inspection, deeper systems inspection
Every 500 hours (or 5 years)
100/300-hour items plus timing belt replacement/inspection per model (commonly ~5 years/1,000 hours on many F-series — model-specific, check the manual), VST service on applicable models
1,000 hours +
Major-service territory: timing belt, valve clearance, full fuel-system and cooling-system overhaul evaluation

Standing rules

  • Gear oil: changed at 20 hr, then every 100 hr / annually. Milky oil = water in the lower unit = reseal it (pressure/vacuum test finds the leak).
  • Impeller: inspect at 100 hr, replace by 300 hr / 3 years no matter how good it looks. Saltwater and commercial use shorten this.
  • Thermostats: test/replace at the 300-hour service. Stuck open = over-cooling codes (49/58) and poor running; stuck closed = overheat (46/252).
  • Anodes: inspect every service, replace at about half consumed. Never paint an anode.
  • Fuel filters: engine filter + boat-side separator on the 100-hr cycle, separator element ~50 hr. Ethanol fuel + water-in-fuel code 27? Look here first.
  • Spark plugs: NGK, model-specific — F115B takes LKR6E, gap 0.8–0.9 mm; earlier F115 takes LFR6A-11, gap 1.0–1.1 mm. Gap and torque from the manual, every time.

Tools — every day (the roll cart)

  • YDIS laptop — codes, live data, hour history, actuator tests, TPS/ETV setup. Dealer-licensed; the single most important diagnostic tool on a modern Yamaha.
  • Digital multimeter (a good one) — voltage, voltage-drop-under-load, continuity, sensor/coil resistance, AC ripple. Half of "electronic" faults are found with this, not the laptop.
  • Compression gauge with the right plug-thread adapters — engine warm, plugs out, throttle open, strong battery, same crank count per cylinder, write every number down.
  • Fuel pressure + vacuum gauge set — rail pressure on EFI motors; vacuum on the boat-side supply finds restrictions and air leaks. Test the boat's fuel system as a system, not just the engine.
  • Spark tester (inline, adjustable-gap) — proves spark strength safely.
  • Timing light — ignition timing on applicable models.
  • Hand tools + torque wrenches (in-lb and ft-lb) — Yamaha specs are metric/N·m; plugs and lower-unit hardware live and die by torque.
  • Flushing muffs / test tank, gear oil pump, prop wrench and blocks.
  • YDIS Smart app — quick phone check on compatible motors; not a substitute for the laptop.

Tools — diagnostic deep work (the back shelf)

  • Leak-down tester — when compression is low, tells you where it's going: intake valve, exhaust valve, head gasket, or rings.
  • Lower-unit pressure & vacuum testers — find seal leaks; vacuum-test shaft seals after a reseal.
  • Borescope — cylinders, VST internals, corrosion checks without teardown.
  • Injector test/clean rig + VST service kit — where EFI fuel faults (codes 25/26/62) end up.
  • Yamaha specialty tools — flywheel holder/puller, valve shim tools, lower-unit bearing/carrier pullers, shift-shaft and driveshaft tools, powerhead lifting eye. The service manual lists the special tool numbers.
  • Oscilloscope — pulser/crank sensor faults (codes 13/14) that pass a resistance test but fail in real life.
  • Load tester / conductance battery tester — separates "bad battery" from "bad charging system" (code 19).
  • Infrared thermometer — compare head temps side to side; spot a thermostat that never opens.
  • The factory service manual for the exact model — torque specs, wiring diagrams, code test procedures. Nothing above replaces it.

Quick-reference numbers

Only numbers with a source behind them. Yamaha publishes most specs per model — when a number names a model, it belongs to that model.

Battery resting voltage (fully charged, settled)
~12.6 V
Source: ABYC exam materials / standard marine electrical references
Charging voltage at battery, engine running
~13.5–14.5 V (techs accept up to ~14.9 on a healthy system; no rise over resting voltage = regulator/rectifier fault; sustained well above 15 V = overcharge)
Source: Yamaha tech Q&A, JustAnswer (F115/F200 charging cases)
AC ripple at battery @ ~2,000 RPM
Under 250 mV AC — over that, rectifier diodes are leaking
Source: Yamaha tech Q&A, JustAnswer (F200 regulator diagnosis)
Idle speed, in neutral — F115B/F130A
700–800 RPM; full-throttle range 5,300–6,300 RPM
Source: Yamaha F115 owner's manual specifications (2022)
Idle speed — earlier F115 (F115TRA era)
700–800 RPM; WOT 5,000–6,000 RPM; gear ratio 2.15:1
Source: Yamaha F115 owner's manual data (manualmachine)
Idle speed — carbureted 150 2-stroke (in gear, in water)
675–725 RPM
Source: Yamaha tech Q&A, JustAnswer
Full-throttle range — F150 (2.00:1 gear)
5,000–6,000 RPM
Source: Yamaha F150 published specs
High-pressure fuel rail — F115 EFI
~43–44 psi and steady at all RPM; low-pressure (lift) pump output at least ~3 psi
Source: Yamaha tech Q&A, JustAnswer (F115 fuel cases)
Low-pressure fuel pump — carbureted Pro V 150
3–7 psi
Source: Yamaha tech Q&A, JustAnswer
Cranking compression — example minimum
107 psi minimum on the F250-family model in the cited service-manual excerpt; Yamaha notes up to ~30 psi spread between cylinders can be normal on that model. Healthy F-series motors commonly test ~145–190 psi; the universal rule: cylinders within ~10% of each other, none below the model's manual minimum
Source: Yamaha factory service manual excerpt via JustAnswer / The Hull Truth
Compression — small/older motors rule of thumb
100+ psi is healthy, 75+ psi will usually still run on small motors — rule of thumb only, not a Yamaha spec
Source: Yamaha tech Q&A, JustAnswer (25 HP case)
Voltage drop limits (ABYC)
≤3% critical circuits, ≤10% non-critical
Source: ABYC E-11 standard, via ABYC references
Prop slip at WOT
~5–15% typical healthy range
Source: Omni Calculator / marine prop references
Spark plug gap — F115B
0.8–0.9 mm (0.031–0.035″), NGK LKR6E
Source: Yamaha F115 owner's manual (2022)
Spark plug gap — earlier F115
1.0–1.1 mm (0.039–0.043″), NGK LFR6A-11
Source: Yamaha F115 owner's manual data
Battery spec — F115
430–1080 CCA; 70 Ah (20HR); max generator output 35 A
Source: Yamaha F115 owner's manual (2022)

Deliberately NOT printed: a universal "Yamaha compression spec," thermostat opening temps, or one fuel pressure for every motor — Yamaha publishes those per model in the service manuals, and a wrong universal number is worse than none.

🌊 ON THE WATER

Lowcountry water, live: the tide where you're headed, the landings near where you're standing, and the charted depth under the boat — added to the tide right now, so you can sanity-check the depth finder.

🌊 Tides

Loading the tide board…

📍 Boat landings near you

🗺️ Depth where you are

The chart gives the range for the area. Your depth meter is the truth under the boat.

🎣 SEASONS & PAPERWORK

South Carolina seasons at a glance — what's open, what's not, and the limits that go with them — plus every state counter for licenses and boat paperwork, all in one place.

🎣 South Carolina seasons

Season dates are set by SCDNR each year — the dates below are the current published ones, and the pill on each card reads off today's date. When it matters, the state's page is the final word.

🦐 Shrimp Baitingchecking…

Season: Sep 11 (noon) – Nov 9 (noon)

48 quarts whole (29 headed) per day per set of poles. Takes the shrimp baiting license — there's a button for it below. Cast-netting shrimp with NO bait is a different thing: food-shrimp openings are announced by SCDNR — check the SCDNR shrimp page.

🦪 Oysters & Clamschecking…

Season: Oct 1 – May 15

Public and State Shellfish Grounds. Limit: 2 bushels of oysters + ½ bushel of clams a day, no more than 2 days in any 7. A saltwater fishing license is required — button below. Beds can close after storms or spills, so check before you go: SCDES hotline 1-800-285-1618.

🦀 Blue Crabchecking…

Season: no closed season

A saltwater license covers up to 2 crab pots; up to 3 handlines, fold-up traps, or drop nets need no license at all. Size limits apply.

🐟 Fish Seasons & Limits

Most saltwater fish are year-round with size and bag limits — a few (like cobia) have their own seasons. The whole list lives with the state:

📏 SCDNR Saltwater Rules & RegulationsSize limits, bag limits, and the seasonal fish — straight from SCDNR.

🎣 Licenses — South Carolina

🎣 Buy a SC Saltwater Fishing LicenseThe one license that covers saltwater fishing — and you need it for oysters, clams, and crab pots too. The price is on the state's page. 🦐 Shrimp Baiting LicenseSame state counter — when you get there, pick the Shrimp Baiting License. 📞 Or by phone: 1-866-714-3611SCDNR license sales — 24 hours a day, 7 days a week.

📋 Boat paperwork

🚤 SC: Register or Title a Boat / MotorJust bought a boat — start here. Sold one? The title transfer lives here too. 🔁 SC: Renew Boat RegistrationStickers expiring — renew here. 🛥️ NC: Register a BoatPutting a boat on North Carolina water — register or title it with NC Wildlife. 🎣 NC: Fishing LicenseFishing North Carolina water — get the license here first. ⚓ USCG Captain's License (NMC)The six-pack itself — requirements, checklists, and forms at the National Maritime Center. The ⚓ Sea Time Log on this page feeds it.

The app doesn't take your money or your application — these buttons walk you to the state's own counter.

Honest note: there's no official public Yamaha practice exam. The strongest play is your own course books + the listening rotation + YDIS reps at work. More coming to this brain soon — this page is the start of the Boat Motor Brain.

— Built with pride by Dad. This is your turn to get it. 🇺🇸